Bk-precision 9171-9174 - Manual User Manual Page 178
- Page / 187
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
166
Figure 35- Dual Channel External Analog Input Calibration
2. Connect the 10VDC source to the analog inputs on the
DIO/Analog Interface Card as shown in Figure 36 for single
channel.
Figure 36- Single Channel Analog Control Calibration Setup
3. Set the DC source to output 1.000 V and wait for approximately
5 seconds until the output voltage is stable. Press to finish
the first step.
4. Next, change the output of the DC source to 9.000 V and follow
the same as step 3.
CH 1 EXT . CURR Res = Start
CH 2 EXT . VOLT Res = Start
CH 2 EXT . CURR Res = Start
Calib EXT . Lo Volt = 1 . 000 V
Calib EXT . Lo Volt = 9 . 000 V
CH 1 EXT . VOLT Res = Start
Enter
- Programmable DC Power 1
- Supplies 1
- Safety Summary 3
- KEEP AWAY FROM LIVE CIRCUITS 4
- WARNINGS AND CAUTIONS 4
- Compliance Statements 6
- CE Declaration of Conformity 7
- Safety Symbols 8
- Table of Contents 9
- 1 General Information 13
- 1.1 Product Overview 13
- 1.2 Package Contents 14
- 1.3 Front Panel Overview 15
- Front Panel Description 17
- 1.4 Rear Panel Overview 18
- 3124 26 27 19
- 1.5 Optional Accessories 20
- 1.6 Display Overview 21
- Display Description 22
- 5 . 000 V1 . 000 A 22
- Removing Interface Cards 24
- 1.8 Rackmount Installation 25
- 2 Getting Started 30
- 2.2 Line Voltage Selection 31
- Line Voltage Switch 32
- 2.3 Output Connections 33
- 2.4 Preliminary Check 35
- Voltage Check 37
- Current Check 38
- 3 Front Panel Operation 40
- 3.1 Menu Options 40
- How to Access the Menu 41
- 3.2 Remote Interface Setup 44
- GPIB Interface 46
- Ethernet (LAN) Interface 46
- RS-232 Interface 47
- RS-485 Interface 48
- LCD Backlight Timer 51
- Key Lock 51
- Disabling Key Sound 52
- Voltage Limit Set 55
- Current Limit Set 56
- Setting Voltage 57
- OFF200 . 00 V 1 . 000 A 58
- CH1 OFF5 . 000 V1 . 000 A 58
- OFF5 . 000 V 1 . 000 A 58
- Setting Current 59
- SET = 2.000 A 60
- 5 . 000 V 2 . 000 A 60
- Enable/Disable Output 61
- CH1CV5 . 000 V1 . 000 A 62
- CH2CV5 . 000 V1 . 000 A 62
- CV5 . 000 V1 . 000 A 62
- Slew Rate Configuration 63
- Output Timer Function 65
- CH1OFF10 . 000 V1 . 000 A 66
- CH2OFF10 . 000 V1 . 000 A 66
- OFF10 . 000 V1 . 000 A 66
- Measurement Average Setting 67
- Multi/Single Output Control 67
- Local Sense 69
- Remote Sense 70
- DO NOT CONNECT LIKE BELOW: 72
- LED Mode 74
- LED MODE = ON 74
- Low Current Mode 76
- LED MODE = OFF 77
- Low Current MODE = ON 77
- 3.9 Output Protection 78
- Configure OCP 79
- Save Output Settings 80
- MEM = 0 81
- Recall Output Settings 82
- Configure Power-On State 82
- 3.11 Sequence Program Mode 83
- 3.12 External Analog Control 84
- Voltage Control 85
- Resistance Control 86
- 0 – 5 kΩ 0 – 5 kΩ 87
- 0.00 V 0.00 A 88
- 3.13 Digital I/O 89
- 3.14 Display Errors 93
- 4 Remote Operation 95
- 4.1 Interface Connection 95
- Table 6- RS-232 Pin Out 96
- Figure 27- GPIB Interface 96
- Ethernet (LAN) 97
- 4.2 Remote Commands 102
- Parameter Definitions 103
- Remote Commands 103
- Common SCPI Commands 104
- SCPI Command Subsystem 105
- GPIOSubsystem 108
- Measure Subsystem 110
- Memory Subsystem 111
- MEMory:ISET 112
- MEMory:ISET2 112
- Output Subsystem 113
- OUTput:MIN:VOLT2 116
- OUTput:MIN:CURRent 116
- OUTput:MIN:CURR2 116
- OUT2 Subsystem 118
- Program Subsystem 119
- PROGram:STEP:CURRent 122
- PROGram:STEP:CURR2 122
- PROGram:STEP:ONTime 122
- PROGram:STEP:VOLTage 123
- PROGram:STEP:VOLT2 123
- PROGram:TOTAl 123
- Protection Subsystem 124
- Source Subsystem 127
- System Subsystem 129
- Timer Subsystem 135
- Standard Commands 136
- 4.3 Sequence Programming 146
- 4.4 Multi Unit Programming 150
- Remote Commands via USB 151
- CPV/CPV2 154
- CMV?/CMV2? 154
- CPC/CPC2 154
- CMC?/CMC2? 154
- CDVC?/CDVC2? 155
- COUT/COUT2 155
- COV/COV2 155
- COVP/COVP2 156
- COC/COC2 156
- COCP/COCP2 156
- Examples 157
- GOUT/GOUT2 160
- GOV/GOV2 160
- GOVP/GOVP2 160
- GOC/GOC2 160
- Error List 161
- 5 Troubleshooting Guide 162
- Remote Control 164
- 6 Specifications 165
- 7 Calibration 170
- Requirements 171
- Current Calibration 171
- 6 ½ Digit DMM 172
- CALIB OCP Hi = Start 174
- CALIB OCP Lo = Start 174
- Voltage Calibration 175
- CALIB OVP Hi = Start 176
- CALIB OVP Lo = Start 176
- Voltage 179
- SERVICE INFORMATION 183
- LIMITED THREE-YEAR WARRANTY 184
© 2020, manymanuals.com. All rights reserved. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals